_ |
|||
EPA |
Chemical |
||
Hazardous |
Abstracts |
Regulatory |
|
Waste |
Service |
Level |
|
Number |
Contaminant |
Number |
Mg/l |
_ |
|||
D004 |
Arsenic |
7440-38-2 |
5.0 |
D005 |
Barium |
7440-39-3 |
100.0 |
D018 |
Benzene |
71-43-2 |
0.5 |
D006 |
Cadmium |
7440-43-9 |
1.0 |
D019 |
Carbon tetrachloride |
56-23-5 |
0.5 |
D020 |
Chlordane |
57-74-9 |
0.03 |
D021 |
Chlorobenzene |
108-90-7 |
100.0 |
D022 |
Chloroform |
67-66-3 |
6.0 |
D007 |
Chromium |
7440-47-3 |
5.0 |
D023 |
o-Cresol |
95-48-7 |
200.0 [FN1] |
D024 |
m-Cresol |
108-39-4 |
200.0 [FN1] |
D025 |
p-Cresol |
106-44-5 |
200.0 [FN1] |
D026 |
Cresol |
200.0 [FN1] |
|
D016 |
2,4-D |
94-75-7 |
10.0 |
D027 |
1,4-Dichlorobenzene |
106-46-7 |
7.5 |
D028 |
1,2-Dichloroethane |
107-06-2 |
0.5 |
D029 |
1,1-Dichloroethylene |
75-35-4 |
0.7 |
D030 |
2,4-Dinitrotoluene |
121-14-2 |
0.13 |
D012 |
Endrin |
72-20-8 |
0.02 |
D031 |
Heptachlor (and its epoxide) |
76-44-8 |
0.008 |
D032 |
Hexachlorobenzene |
118-74-1 |
0.13 |
D033 |
Hexachlorobutadiene |
87-68-3 |
0.5 |
D034 |
Hexachloroethane |
67-72-1 |
3.0 |
D008 |
Lead |
7439-92-1 |
5.0 |
D013 |
Lindane |
58-89-9 |
0.4 |
D009 |
Mercury |
7439-97-6 |
0.2 |
D014 |
Methoxychlor |
72-43-5 |
10.0 |
D035 |
Methyl ethyl ketone |
78-93-3 |
200.0 |
D036 |
Nitrobenzene |
98-95-3 |
2.0 |
D037 |
Pentachlorophenol |
87-86-5 |
100.0 |
D038 |
Pyridine |
110-86-1 |
5.0 [FN2] |
D010 |
Selenium |
7782-49-2 |
1.0 |
D011 |
Silver |
7440-22-4 |
5.0 |
D039 |
Tetrachloroethylene |
127-18-4 |
0.7 |
D015 |
Toxaphene |
8001-35-2 |
0.5 |
D040 |
Trichloroethylene |
79-01-6 |
0.5 |
D041 |
2,4,5-Trichlorophenol |
95-95-4 |
400.0 |
D042 |
2,4,6-Trichlorophenol |
88-06-2 |
2.0 |
D017 |
2,4,5-TP (Silvex) |
93-72-1 |
1.0 |
D043 |
Vinyl chloride |
75-01-4 |
0.2 |
_ |
|||
[FN1]1 If o-, m- and p-Cresol concentrations cannot be differentiated, the total cresol (D026) concentration is used. The regulatory level of total cresol is 200 mg/l.
[FN2]2 Quantitation limit is greater than the calculated regulatory level. The quantitation limit therefore becomes the regulatory level .
_ |
||
STLC |
TTLC |
|
Wet-Weight |
||
Substancea,b |
mg/l |
mg/kg |
_ |
||
Antimony and/or antimony compounds |
15 |
500 |
Arsenic and/or arsenic compounds |
5.0 |
500 |
Asbestos |
1.0 |
|
(as percent) |
||
Barium and/or barium compounds (excluding |
||
barite) |
100 |
10,000 c |
Beryllium and/or beryllium compounds |
0.75 |
75 |
Cadmium and/or cadmium compounds |
1.0 |
100 |
Chromium (VI) compounds |
5 |
500 |
Chromium and/or chromium (III) compounds |
5 d |
2,500 |
Cobalt and/or cobalt compounds |
80 |
8,000 |
Copper and/or copper compounds |
25 |
2,500 |
Fluoride salts |
180 |
18,000 |
Lead and/or lead compounds |
5.0 |
1,000 |
Mercury and/or mercury compounds |
0.2 |
20 |
Molybdenum and/or molybdenum compounds |
350 |
3,500 e |
Nickel and/or nickel compounds |
20 |
2,000 |
Selenium and/or selenium compounds |
1.0 |
100 |
Silver and/or silver compounds |
5 |
500 |
Thallium and/or thallium compounds |
7.0 |
700 |
Vanadium and/or vanadium compounds |
24 |
2,400 |
Zinc and/or zinc compounds |
250 |
5,000 |
_ |
||
aSTLC and TTLC values are calculated on the concentrations of the elements, not the compounds.
b In the case of asbestos and elemental metals, the specified concentration limits apply only if the substances are in a friable, powdered or finely divided state. Asbestos includes chrysotile, amosite, crocidolite, tremolite, anthophyllite, and actinolite.In the case of asbestos and elemental metals, the specified concentration limits apply only if the substances are in a friable, powdered or finely divided state. Asbestos includes chrysotile, amosite, crocidolite, tremolite, anthophyllite, and actinolite.In the case of asbestos and elemental metals, the specified concentration limits apply only if the substances are in a friable, powdered or finely divided state. Asbestos includes chrysotile, amosite, crocidolite, tremolite, anthophyllite, and actinolite.
c excluding barium sulfate.
d If the soluble chromium, as determined by the TCLP set forth in Appendix I of chapter 18 of this division, is less than 5 mg/l, and the soluble chromium, as determined by the procedures set forth in Appendix II of chapter 11, equals or exceeds 560 mg/l and the waste is not otherwise identified as a RCRA hazardous waste pursuant to section 66261.100, then the waste is a non-RCRA hazardous waste.
e Excluding molybdenum disulfide.
_ |
||
STLC |
TTLC |
|
Wet Weight |
||
Substance |
mg/l |
mg/kg |
_ |
||
Aldrin |
0.14 |
1.4 |
Chlordane |
0.25 |
2.5 |
DDT, DDE, DDD |
0.1 |
1.0 |
2,4-Dichlorophenoxyacetic acid |
10 |
100 |
Dieldrin |
0.8 |
8.0 |
Dioxin (2,3,7,8-TCDD) |
0.001 |
0.01 |
Endrin |
0.02 |
0.2 |
Heptachlor |
0.47 |
4.7 |
Kepone |
2.1 |
21 |
Lead compounds, organic |
- |
13 |
Lindane |
0.4 |
4.0 |
Methoxychlor |
10 |
100 |
Mirex |
2.1 |
21 |
Pentachlorophenol |
1.7 |
17 |
Polychlorinated biphenyls (PCBs) |
5.0 |
50 |
Toxaphene |
0.5 |
5 |
Trichloroethylene |
204 |
2,040 |
2,4,5-Trichlorophenoxypropionic acid |
1.0 |
10 |
_ |
||
where C (in parts per million) is the concentration of material A in head space vapor, Q (in milligrams) is the quantity of material A in sampling syringe and MW (in milligrams per millimole) is the molecular weight of material A. Where an acute inhalation LC 50 is not available, an LC 50 measured for another time (t) may be converted to an eight-hour value with the following equation:
Eight-hour LC 50 = (t/8) x (t-hour LC 50).
where %A x is the weight percent of each component in the waste mixture and TA X is the acute oral or dermal LD 50 or the acute oral LD LO of each component.
Cal. Code Regs. Tit. 22, § 66261.24
Note: Authority cited: Sections 25141, 25159, 58004 and 58012, Health and Safety Code. Reference: Sections 25117, 25120.2,25141, 25159 and 25159.5, Health and Safety Code and 40 CFR Section 261.24.